DieHard 71341 Bedienungshandbuch PDF herunterladen (Seite 6)

• 6 •

7. FOLLOW THESE STEPS WHEN BATTERY IS OUTSIDE VEHICLE

A SPARK NEAR THE BATTERY MAY

CAUSE A BATTERY EXPLOSION. TO

REDUCE THE RISK OF A SPARK NEAR

THE BATTERY:

7.1 Check polarity of battery posts. POSITIVE

(POS, P, +) battery post usually has a larger

diameter than NEGATIVE (NEG, N, –) post.

7.2 Attach at least a 24-inch-long 6-gauge

(AWG) insulated battery cable to

NEGATIVE (NEG, N, –) battery post.

7.3 Connect POSITIVE (RED) charger clip to

POSITIVE (POS, P, +) post of battery.

7.4 Position yourself and free end of cable as

far away from battery as possible – then

connect NEGATIVE (BLACK) charger clip

to free end of cable.

7.5 Do not face battery when making nal

connection.

7.6 When disconnecting charger, always do

so in reverse sequence of connecting

procedure and break rst connection

while as far away from battery as

practical.

7.7 A marine (boat) battery must be removed

and charged on shore. To charge it on

board requires equipment specially

designed for marine use.

8. GROUNDING AND AC POWER CORD CONNECTIONS

This battery charger is for use on a nominal

120 volt circuit and has a grounded plug.

The charger must be grounded, to reduce

the risk of electric shock. The plug must

be plugged into an outlet that is properly

installed and grounded in accordance with

all local codes and ordinances. The plug

pins must t the receptacle (outlet). Do not

use with an ungrounded system.

DANGER: Never alter the AC cord or

plug provided – if it does not t the outlet,

have a proper grounded outlet installed

by a qualied electrician. An improper

connection can result in a risk of an

electric shock or electrocution.

NOTE: Pursuant to Canadian

Regulations, use of an adapter plug

is not allowed in Canada. Use of an

adapter plug in the United States is not

recommended and should not be used.

USING AN EXTENSION CORD

The use of an extension cord is not

recommended. If you must use an

extension cord, follow these guidelines:

•Pins on plug of extension cord must be

the same number, size, and shape as

those of plug on charger.

•Ensure that the extension cord is

properly wired and in good electrical

condition.

•Wire size must be large enough for

the AC ampere rating of charger, as

specied:

Length of cord (feet) 25 50 100 150

AWG* size of cord 14 12 10 8

*AWG-American Wire Gauge

9. ASSEMBLY INSTRUCTIONS

9.1 Remove all cord wraps and uncoil the

cables prior to using the battery charger.

9.2 Extend the handle from the retracted

position by pulling it upward until it locks

into place. (Press the small silver buttons

inward, if necessary.)

10. CONTROL PANEL

ON/OFF SWITCH

Use this switch to select between the

Charge/Maintain rate, Boost rate and the

Engine Start mode.

•OFF – When the switch is in this position

(middle), the charger is turned off.

•BOOST or CHARGE/MAINTAIN –

When the switch is in this position, the

Rate Selection button can be set to either

the 6<>2A Charge/Maintain or the

50A Boost setting.

•ENGINE START – When the switch is

in this position, the Engine Start LED will

illuminate.

DIGITAL DISPLAY

The Digital Display gives a digital

indication of voltage, % of charge or

time. The display will show the battery

VOLTAGE when the charger is not

charging a battery. When it goes

into charging mode, the display will

automatically change to ON (to show

charging has started) and either 6 or 12

(the voltage of the battery, determined

by the charger). If you manually stop the

charging process (by pressing the Rate

Selection button) before the battery is fully

charged, the display will show Off.

1 2 3 4 5 6 7 8 9 10

Kommentare zu diesen Handbüchern

Keine Kommentare

DieHard 71341 Bedienungshandbuch Seite 6

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Ladegeräte DieHard 71341