DieHard 71341 Bedienungshandbuch PDF herunterladen (Seite 8)

• 8 •

8. With the charger plugged in and

connected to the battery of the

vehicle, set the switch to the Boost or

Charge/Maintain position.

9. Select the desired rate and battery type.

10. When disconnecting the charger,

set the switch to the OFF position,

disconnect the charger from the AC

power, remove the clamp from the

vehicle chassis, and then remove the

clamp from the battery terminal.

CHARGING A BATTERY

OUTSIDE OF THE VEHICLE

1. Place battery in a well-ventilated area.

2. Clean the battery terminals.

3. Set the switch to the OFF position.

4. Connect the battery, following the

precautions listed in sections 6 and 7.

5. Connect the charger to the electrical

outlet.

6. With the charger plugged in and

connected to the battery of the vehicle,

set the switch to the Boost or Charge/

Maintain position.

7. Select the desired rate and battery type.

8. When disconnecting the charger,

set the switch to the OFF position,

disconnect the charger from the AC

power, disconnect the negative clamp,

and nally the positive clamp.

9. A marine (boat) battery must be

removed and charged on shore.

USING THE ENGINE START FEATURE

Your battery charger can be used to jump

start your car if the battery is low. Follow

all safety instructions and precautions for

charging your battery. Wear complete eye

protection and protective clothing.

WARNING: Using the ENGINE START

feature WITHOUT a battery installed

in the vehicle will damage the vehicle’s

electrical system.

NOTE: If you have charged the battery

and it still will not start your car, do not

use the Engine Start feature, or it will

damage the vehicle’s electrical system.

Have the battery checked.

1. Set the switch to the OFF position.

2. With the charger unplugged from the

AC outlet, connect the charger to the

battery following the instructions given

in the CHARGING A BATTERY IN

THE VEHICLE section.

3. Plug the charger AC power cord into

the AC outlet.

4. With the charger plugged in and

connected to the battery of the vehicle,

set the ON/OFF switch to the Engine

Start position. The Engine Start LED

will illuminate.

5. Crank the engine until it starts or 5

seconds pass. If the engine does not

start, wait 3 minutes before cranking

again. This allows the charger and

battery to cool down.

NOTE: During extremely cold weather, or if

the battery is under 2 volts, boost the battery

for 5 minutes before cranking the engine.

6. If the engine fails to start, use the

50A Boost rate for 5 minutes before

attempting to crank the engine again.

7. After the engine starts, move the switch

to the OFF position and unplug the AC

power cord before disconnecting the

battery clips from the vehicle.

8. Clean and store the charger in a dry

location.

NOTE: If the engine does turn over but

never starts, there is not a problem with

the starting system; there is a problem

somewhere else with the vehicle. STOP

cranking the engine until the other problem

has been diagnosed and corrected.

AUTOMATIC CHARGING MODE

When an Automatic Charge is performed,

the charger switches to the maintain mode

automatically after the battery is charged.

ABORTED CHARGE

If charging cannot be completed normally,

charging will abort. When charging

aborts, the charger’s output is shut off,

the CHARGING

(yellow/orange) LED will

ash, and the display will show an error

code. To reset after an aborted charge,

unplug the charger from the AC outlet,

wait a few moments and plug it back in.

DESULFATION MODE

Desulfation could take 8 to 10 hours. If

desulfation fails, charging will abort, the

CHARGING

(yellow/orange) LED will

ash, and the display will show F02.

COMPLETION OF CHARGE

Charge completion is indicated by the

CHARGED/MAINTAINING (green) LED.

When pulsing, the charger has switched to

the maintain mode of operation.

MAINTAIN MODE

(FLOAT-MODE MONITORING)

When the CHARGED/MAINTAINING

(green) LED is pulsing, the charger has

started maintain mode. In this mode, the

charger keeps the battery fully charged

by delivering a small current when

necessary. If the charger has to provide

its maximum maintain current for a

continuous 12 hour period, it will go into

abort mode (see Aborted Charge section).

This is usually caused by a drain on the

battery or the battery could be bad. Make

sure there are no loads on the battery. If

there are, remove them. If there are none,

have the battery checked or replaced.

1 2 3 4 5 6 7 8 9 10

Kommentare zu diesen Handbüchern

Keine Kommentare

DieHard 71341 Bedienungshandbuch Seite 8

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Ladegeräte DieHard 71341